DIRECTPAD PRO DRIVER

After making sure all the connections are correct you did this first didn't you? No, I am not mistaken, yellow wire is 12v, but for that we have voltage regulator LCV: If, once connected, they both do not work, chances are your parallel port is not able to feed both pads the 5v power they need. If you pay attention, hole 6 of the female connector must go connected to pins 18 and 19 of connector DB Soldering the diodes Now for the delicate part.

Uploader:	Meztijora
Date Added:	24 July 2007
File Size:	54.48 Mb
Operating Systems:	Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads:	89548
Price:	Free* [*Free Regsitration Required]

| DirectPad Pro | Nihongo

Be aware that this interface is different from SnesKey's interface. In theory if first pad works the second would have to also work perfectly. The other wire the black you solder to pin 18 or 19 or where it connected the wire that corresponds of hole 6.

Maybe diredtpad to Calibrate the controller. If your controller doesn't power up many racing controllers need more power than the parallel port can supply, for example you may want to try adding an external 5V power supply: If your controller doesn't power up many racing controllers need more power than the parallel port can supply, for example you may want to try adding an external 5V power supply:.

Take the female connector of the cable and put the pin in each one of the holes to make contact and, using the multi-meter on resistant setting, write down to what hole corresponds each wire of the other end.

Next we will take the DB connector with the corresponding tin-plated ends you did do in the previous section and solder the short ends of each one of the diodes in ends 5, 6, 7, 8 and 9 of the DB connector. If you have a dual-shock compatible pad make sure it has 8 wires.

Win9X Direct Pad Pro 5 installation

The optional line is only necessary if you are running a Dual-Shock pad, and directpas to use force feedback. Well, we now have written on the paper the relation of the holes from the 1 to the 9 and to what cable color in the other end corresponds to each one of them. In theory it would have to work with any control system directpwd game for PlayStation pad of another mark, steering wheel, etc.

Now dirrectpad each one of these wires except the one that does not have insulator that you can cut it directly removing little insulation from the ends of the wires so you have bare wire. You can go through the other settings and tabs to completely change everything but for the first time you should leave most of it alone.

Directpqd will be able to use ALL the buttons of PlayStation pad in your preferred games, altogether 10 if you use digitals or 16 if you use the analog control. Connecting a second PlayStation Pad to the same parallel port.

The connection goes to the parallel port, which means that if you are going to use the printer you change connectors Solder the wire to the end of the central diode and solder the 5 diodes together as it appears in the circuit. Before executing the game enter pdo configuration and select it in Properties of driver.

The assembly is not very complicated. If you're having troubles, and have already double-checked the wiring and diode orientation, try using the Advanced tab in the control panel and increasing the PSX scan delay.

Soldering the diodes Now for the delicate part. Keep this paper in a safe place that you will need it later.

Scissors or wire cutters. Those that we have in the section Complements for pads of 6 and 8 buttons do not give problems. Nothing of anything in the driver works. So if you don not want to do this you don't have to. Now we take the soldering iron and tin-plate the end of each diode taking care that you do not taking too long doing it or you can damage the diode by the heat. For me I had to click Add To hook up the second controller duplicate all connections except DB and DB Tin-plating DB connectors Take DB connector and tin-plate the ends where we are going to make the connections, that are 2, 3, 4, 5, 6, 7, 8, 9, 10, 12, 18 and Before beginning with the explanation I must make clear to you that I have not made the assembly.

Once connected everything it gives just as it is dual-shock or notwe verified in the configuration of the driver none of the buttons nor any directional ones work. You should be able to configure the second pad the same as you did for pad one. Now you must do is to install another a second DirectPad driver the same way that you did the first time but this time. Connect the 5v to pin 5 of the pad were the diodes connected and the ground to pins 18 and 19 of the DB connector.

Lro most common problem is that it does not do anything.